I started off this week by designing the code for a passive buzzer. It was quite a simple task as I only made a few changes compared to the previous design made, they only have outputs that needed to be sent without having to read the inputs. I ran my codes but to my disappointment there was no sound coming from the buzzer at all. Just silence. The frequency range that humans can hear are from 20 Hz to 20 Read more
I was having unfinished work from last week of not having the results I wanted from the test bench. The acknowledge signal of Wishbone does not behave as what was expected. I edited the design code but it still did not work correctly. I asked Dr. Shawn about this and he said it was not about the design code but my test bench was written wrong. I still could not get it right after Dr. Shawn told me what to Read more
It’s already week 3. Time flies on internship. Its really not boring either. I sometimes spend +8 hours in the office but I’m never thinking “Oh man when can I leave?” Instead its “shit I’ve been here for 10 hours I should probably leave”. This week’s work was a continuation of last weeks’. First I wanted to make my tests better by not using “no operation for loops” as delays. It would take a different amount of time on every board even when they were all programmed Read more
This was my second week here. I was tasked with troubleshooting and characterizing the boards. There are in total seven prototypes for me to play with. The boards are divided into old and new boards. The main differences are that the new boards use slightly different PIC32 and Spartan-6 chips. And the LAN chip on the new boards is driven by a different clock source than on the old ones. Now some of these boards have issues. Some of them Read more
On Monday, I was almost done with the design code for my first module, a 7 colour auto flash LED. I chose this module to start with as it is quite simple to program (only outputs), in the hopes that I can finish it quick. However, what seem simplest is still quite hard for me as my skills in interpreting schematic to be turned into codes are still weak. I definitely will not be able to design it without the Read more
I was stucked with my work when I could not program the board as I wanted. I made a program of LED blinking and LED being turned on and off using switches. After I synthesized and generate the programming bit file, I used iMPACT to load it to the board but I keep getting “Program Failed”. I checked my codes and started to think that the software or the board is not working as it should. After I tried to Read more
This week I spent most of my time testing the networking section of the board. Firstly I tried to run a simple TCP server code on the board to confirm that it is working. unfortunately, I could not get any result from the board. That called for serious debugging and problem-solving. I then tried to check the input voltages on the ethernet chip, just to make sure, the chip is connected to power. The test suggests there are no power Read more
Day 1 & 2: Upon my arrival, I was warmly welcomed and informed that Dr. Shawn wasn’t in office today. As a matter of fact, the other interns mentioned to me that the number of days per week that Dr. Shawn is available in the office was based on RNG. One intern in particular (Sina), was working on an in-house designed and programmed board with a PIC MCU and a Spartan FPGA chips. Sina gave me a brief briefing on work and the project. Read more
This week had been exciting for me as now I have the Digilent Atlys Spartan 6 board to play with. Dr. Shawn taught me on USB over IP, to have the board connected to the server. Before doing anything, Dr. Shawn instructed me to go through the reference manual of the board first, this is very important as the connection of the jumpers should be checked before the board gets turned on. Besides the board, now I also have the Read more
This week the board finally arrived and immediately I noticed that the ethernet jack was missing after notifying Dr. Shawn I then started testing the board with an led blink test program and verified the PIC and LEDs are working. I then moved to testing the USB with a simple comport test code to send a string and verified that the USB is connected and working properly. Next step was to test the FPGA, so firstly I tried to put Read more